Cookies
Wir benötigen Ihre Einwilligung zur Verwendung der einzelnen Daten, damit Sie unter anderem Informationen zu Ihren Interessen einsehen können. Klicken Sie auf "OK", um Ihre Zustimmung zu erteilen.
ASTM A27/A27M-20
Standard Specification for Steel Castings, Carbon, for General Application
Name übersetzen
NORM herausgegeben am 1.5.2020
Informationen über die Norm:
Bezeichnung normen: ASTM A27/A27M-20
Ausgabedatum normen: 1.5.2020
SKU: NS-992981
Zahl der Seiten: 4
Gewicht ca.: 12 g (0.03 Pfund)
Land: Amerikanische technische Norm
Kategorie: Technische Normen ASTM
Kategorie - ähnliche Normen:
Die Annotation des Normtextes ASTM A27/A27M-20 :
This specification covers carbon steel castings for general applications. The grades of steels covered here are: Grade N-1, Grade N-2, Grade U-60-30 [415-205], Grade 60-30 [415-205], Grade 65-35 [450-240], Grade 70-36 [485-250] and Grade 70-40 [485-275]. Except for Grades N-1 and U-60-30, all steel castings shall be heat-treated by full annealing, normalizing, normalizing and tempering, or quenching and tempering. Heat treatments shall be performed after castings have been allowed to cool. Heat and product analyses shall be performed wherein specimens shall conform to required chemical composition of carbon, manganese, silicon, sulfur and phosphorus. Except for Grades N-1 and N-2, all steels shall undergo tension test, and shall conform to the following mechanical requirements: tensile strength, yield point, elongation, and reduction of area.
Keywords:
castings, general application, steel,, ICS Number Code 77.140.80 (Iron and steel castings)
Ergänzende Informationen
| 1. Scope | ||||||||
|
1.1 This specification covers carbon steel castings for general applications that require up to 70 ksi (485 MPa) minimum tensile strength. Note 1: The grades covered by this specification represent
materials that are suitable for assembly with other steel castings
or wrought steel parts by fusion welding. It is not intended to
imply that all these grades possess the same degree of weldability
or that the same welding techniques can be used on all castings. It
is the responsibility of the purchaser to establish for himself a
suitable welding technique.
1.2 Several grades and two classes of steel castings are covered, as indicated below. The grade and class desired shall be specified by the purchaser. 1.2.1 Grade N-1—Chemical analysis only. 1.2.2 Grade N-2—Heat treated but not mechanically tested. 1.2.3 Grade U-60-30 [415-205]—Mechanically tested but not heat treated. 1.2.4 Grades 60-30 [415-205], 1.2.5 Class 1 and Class 2 steel castings shall be specified in accordance with 9.2. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||
| 2. Referenced Documents | ||||||||
|
Empfehlungen:
Aktualisierung der technischen Normen
Wollen Sie sich sicher sein, dass Sie nur die gültigen technischen Normen verwenden?
Wir bieten Ihnen eine Lösung, die Ihnen eine Monatsübersicht über die Aktualität der von Ihnen angewandten Normen sicher stellt.
Brauchen Sie mehr Informationen? Sehen Sie sich diese Seite an.
