Cookies
Wir benötigen Ihre Einwilligung zur Verwendung der einzelnen Daten, damit Sie unter anderem Informationen zu Ihren Interessen einsehen können. Klicken Sie auf "OK", um Ihre Zustimmung zu erteilen.
ASTM A354-17e2
Standard Specification for Quenched and Tempered Alloy Steel Bolts, Studs, and Other Externally Threaded Fasteners (Includes all amendments and changes 11/27/2018).
Name übersetzen
NORM herausgegeben am 1.5.2017
Informationen über die Norm:
Bezeichnung normen: ASTM A354-17e2
Ausgabedatum normen: 1.5.2017
SKU: NS-905698
Zahl der Seiten: 8
Gewicht ca.: 24 g (0.05 Pfund)
Land: Amerikanische technische Norm
Kategorie: Technische Normen ASTM
Kategorie - ähnliche Normen:
Die Annotation des Normtextes ASTM A354-17e2 :
This specification covers the chemical and mechanical requirements of quenched and tempered alloy steel bolts, studs, and other externally threaded fasteners. All fasteners shall be made from alloy steel conforming to the chemical composition requirements. Two levels of bolting strength are covered, designated Grades BC and BD. Selection will depend upon design and the stresses and service for which the product is to be used. Hardness, tensile strength, yield strength, elongation, and area reduction shall be tested to meet the requirements prescribed.
Keywords:
alloy steel, bolts, steel, studs ,, ICS Number Code 21.060.10 (Bolts, screws, studs)
Ergänzende Informationen
| 1. Scope | ||||||||||||||||||||||||
|
1.1 This specification2 covers the chemical and mechanical requirements of quenched and tempered alloy steel bolts, studs, and other externally threaded fasteners 4 in. and under in diameter for application at normal atmospheric temperatures, where high strength is required and for limited application at elevated temperature (Note 1). Any alloy steel capable of meeting the mechanical and chemical properties set forth in this specification may be used. Note 1: For bolts, studs, or other externally threaded
fasteners, to be used at elevated temperatures, refer to
Specification A193/A193M.
1.2 Two strength levels are covered, designated Grades BC and BD. Selection will depend upon design and the stresses and service for which the product is to be used. Note 2: Quenched and tempered alloy steel bolts for structural
steel joints up through 11/2 in. in
diameter are covered in Specification F3125/F3125M. For fastener diameter sizes
above 1 1/2 in., Grade BC may be
considered for structural steel bolting where tensile strength
above 120 ksi is necessary and Grade BD may be considered for
structural steel bolting where tensile strength above 150 ksi is
necessary. In this event, additional requirements of Specification
F3125/F3125M, such as head
size, lubricant, and magnetic particle inspection, should be
carefully considered.
1.3 Nuts are covered in Specification A563. Unless otherwise specified, the grade and style of nut for each grade of fastener shall be as follows:
1.4 Optional supplementary requirements
are provided at the end of this standard.
1.5 Terms used in this specification are defined in Terminology F1789 unless otherwise defined herein. 1.6 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||||||||
| 2. Referenced Documents | ||||||||||||||||||||||||
|
Empfehlungen:
Aktualisierung der technischen Normen
Wollen Sie sich sicher sein, dass Sie nur die gültigen technischen Normen verwenden?
Wir bieten Ihnen eine Lösung, die Ihnen eine Monatsübersicht über die Aktualität der von Ihnen angewandten Normen sicher stellt.
Brauchen Sie mehr Informationen? Sehen Sie sich diese Seite an.
