Cookies
Wir benötigen Ihre Einwilligung zur Verwendung der einzelnen Daten, damit Sie unter anderem Informationen zu Ihren Interessen einsehen können. Klicken Sie auf "OK", um Ihre Zustimmung zu erteilen.
ASTM A635/A635M-15
Standard Specification for Steel, Sheet and Strip, Heavy-Thickness Coils, Hot-Rolled, Alloy, Carbon, Structural, High-Strength Low-Alloy, and High-Strength Low-Alloy with Improved Formability, General Requirements for
Automatische name übersetzung:
Standard-Spezifikation für Stahl, Blech und Band, Heavy Stärke Coils , warmgewalzt, Alloy , Kohlenstoff, Strukturelle , High- Strength Low- Legierung, und hochfesten Low- Legierung mit verbesserter Formbarkeit , Allgemeine Anforderungen an
NORM herausgegeben am 1.11.2015
Informationen über die Norm:
Bezeichnung normen: ASTM A635/A635M-15
Anmerkung: UNGÜLTIG
Ausgabedatum normen: 1.11.2015
SKU: NS-620462
Zahl der Seiten: 15
Gewicht ca.: 45 g (0.10 Pfund)
Land: Amerikanische technische Norm
Kategorie: Technische Normen ASTM
Kategorie - ähnliche Normen:
Die Annotation des Normtextes ASTM A635/A635M-15 :
Keywords:
carbon, commercial, drawing, heavy thickness coils, high-strength low-alloy, high-strength low-alloy with improved formability, sheet steel, strip steel,, ICS Number Code 77.140.50 (Flat steel products and semi-products)
Ergänzende Informationen
| 1. Scope | ||||||||||||||||||||||||||
|
1.1 This specification covers the general requirements for hot-rolled, heavy-thickness sheet and strip in coils. 1.2 It applies to Specifications A414/A414M, A424/A424M, and A1018/A1018M. 1.3 This material is available only in coils described as follows:
Note 1: The changes in width limits with the publication of
A635/A635M – 06a result in a
change in tensile testing direction for material from 0.180 in.
[4.5 mm] to 0.230 in. exclusive [6.0 mm exclusive] over 48 in.
[1200 mm] wide, as that material is now covered by Specification
A568/A568M – 06a. The
purchaser is advised to discuss this change with the
supplier.
1.4 In case of any conflict in requirements, the requirements of the individual material specification shall prevail over those of this general specification. 1.5 Annex A1 lists permissible variations in dimensions and mass (see Note 2) in SI [metric] units. The values listed are not exact conversions of the values listed in the inch-pound tables, but instead are rounded or rationalized values. Conformance to Annex A1 is mandatory when the “M” specification is used. Note 2: The term weight is used when inch-pound units are
the standard. However, under SI, the preferred term is mass.
1.6 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.7 This specification and the applicable material specifications are expressed in both inch-pound units and SI units. However, unless the order specifies the applicable “M” specification designation (SI units), the material shall be furnished to inch-pound units. |
||||||||||||||||||||||||||
| 2. Referenced Documents | ||||||||||||||||||||||||||
|
||||||||||||||||||||||||||
Empfehlungen:
Aktualisierung der technischen Normen
Wollen Sie sich sicher sein, dass Sie nur die gültigen technischen Normen verwenden?
Wir bieten Ihnen eine Lösung, die Ihnen eine Monatsübersicht über die Aktualität der von Ihnen angewandten Normen sicher stellt.
Brauchen Sie mehr Informationen? Sehen Sie sich diese Seite an.
