Vorsicht!

In Ihrem Browser ist die Javascript-Aktivierung nicht erlaubt. Einige Funktionen mögen nicht richtig funktionieren. Für vollständige Funktionalität des Internet-Geschäfts empfehlen wir Javascript zu aktivieren. Siehe hier Instruktion, wie man im Ihren Web-Browser JavaScript aktiviert.

Angezeigte Währung: €

Preisanzeige: ohne MWS

Die Norm ASTM B316/B316M-20 1.12.2020 Ansicht

Ergänzende Informationen

ASTM B316/B316M-20

Standard Specification for Aluminum and Aluminum-Alloy Rivet and Cold-Heading Wire and Rods

Name übersetzen

NORM herausgegeben am 1.12.2020

Sprache
Realisierung	PDF - sofortiges Download - 58.70 € PDF + redline - sofort - 70.40 € Gedruckt - 58.70 € Gedruckt + redline - 70.40 €
Zugänglichkeit	AUF LAGER
Preis	58.70 € ohne MWS
58.70 €

Informationen über die Norm:

Bezeichnung normen: ASTM B316/B316M-20
Ausgabedatum normen: 1.12.2020
SKU: NS-1015291
Zahl der Seiten: 8
Gewicht ca.: 24 g (0.05 Pfund)
Land: Amerikanische technische Norm
Kategorie: Technische Normen ASTM

Drucken

Einem Bekannten abschicken

Anfrage

Kategorie - ähnliche Normen:

Rivets

Die Annotation des Normtextes ASTM B316/B316M-20 :

This specification covers wire and rod in the alloys and the tempers suitable for manufacturing rivets and other similar items by cold-heading operations. The products covered by this specification shall be produced by extruding, rolling, or drawing, or a combination thereof, at the option of the producer. For heat-treated tempers, an inspection lot shall consist of an identifiable quantity of material of the same mill form, alloy, temper, and nominal diameter traceable to a heat-treat lot or lots, and subjected to inspection at one time. On the other hand, an inspection lot shall consist of an identifiable quantity of material of the same mill form, alloy, temper, and nominal diameter subjected to inspection for non heat-treated tempers. Samples for chemical analysis shall be taken from the material by drilling, sawing, milling, turning, or clipping a representative piece or pieces to obtain a prepared sample. One tension test per specimen shall be taken. Resistance to stress corrosion cracking for each lot of specimen shall be established by testing the previously selected tension-test samples for lot acceptance purposes. Variations from the specified diameter, length, and straightness shall not exceed the permissible variations prescribed. The material shall be supplied in the mill finish and shall conform by the requirements of this specification and shall be commercially sound.

Keywords:
aluminum alloy, aluminum-alloy rivet, cold-heading rods, cold-heading wire,, ICS Number Code 21.060.40 (Rivets)

Ergänzende Informationen

1. Scope

1.1?This specification covers wire and rod in the alloys (Note 1) shown in Table 1 and the tempers shown in Table 2 [Table 3] and Table 4 [Table 5], suitable for manufacturing rivets and other similar items by cold-heading operations.

Note 1:?Throughout this specification the use of the term Note 2:?For rolled or cold-finished wire and rod, see Specification B211, and for extruded wire and rod, see Specification B221.

1.2?Alloy and temper designations are in accordance with ANSI H35.1/H35.1M. The equivalent Unified Numbering System alloy designations are those of Table 1 preceded by A9, for example, A91100 for aluminum 1100 in accordance with Practice E527.

1.3?For acceptance criteria for inclusion of new aluminum and aluminum alloys in this specification, see Annex A2.

1.4?The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.4.1?The SI units are shown either in brackets or in separate tables.

1.5?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

2. Referenced Documents

MIL-STD-129	Marking for Shipment and Storage Available from Standardization Documents Order Desk, DODSSP, Bldg. 4, Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http://dodssp.daps.dla.mil.
E607-02	Standard Test Method for Atomic Emission Spectrometric Analysis Aluminum Alloys by the Point to Plane Technique Nitrogen Atmosphere
EN 14242	Aluminum and Aluminum Alloys. Chemical Analysis Inductively Coupled Plasma Optical Emission Spectral Analysis
H35.2	Dimensional Tolerances for Aluminum Mill Products
H35.2M	Dimensional Tolerances for Aluminum Mill Products [Metric]
AMS 2772
H35.1/H35.1M	Alloy and Temper Designation Systems for Aluminum
E1251-17a	Standard Test Method for Analysis of Aluminum and Aluminum Alloys by Spark Atomic Emission Spectrometry (Includes all amendments and changes 10/26/2017).
E1004-23	Standard Test Method for Determining Electrical Conductivity Using the Electromagnetic (Eddy Current) Method
E716-16(2021)e2	Standard Practices for Sampling and Sample Preparation of Aluminum and Aluminum Alloys for Determination of Chemical Composition by Spark Atomic Emission Spectrometry (Includes all amendments and changes 9/7/2022).
E527-23	Standard Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)
E34-11	Standard Test Methods for Chemical Analysis of Aluminum and Aluminum-Base Alloys
E29-22	Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
B985-12(2016)	Standard Practice for Sampling Aluminum Ingots, Billets, Castings and Finished or Semi-Finished Wrought Aluminum Products for Compositional Analysis
B918-01	Standard Practice for Heat Treatment of Wrought Aluminum Alloys
B666/B666M-20	Standard Practice for Identification Marking of Aluminum and Magnesium Products
B660-23	Standard Practices for Packaging/Packing of Aluminum and Magnesium Products
B565-20	Standard Test Method for Shear Testing of Aluminum and Aluminum-Alloy Rivets and Cold-Heading Wire and Rods
B557M-15(2023)	Standard Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products (Metric)
B557-15(2023)	Standard Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products
B221-21	Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes
B211-12	Standard Specification for Aluminum and Aluminum-Alloy Rolled or Cold Finished Bar, Rod, and Wire

Empfehlungen:

Aktualisierung der technischen Normen

Wollen Sie sich sicher sein, dass Sie nur die gültigen technischen Normen verwenden?
Wir bieten Ihnen eine Lösung, die Ihnen eine Monatsübersicht über die Aktualität der von Ihnen angewandten Normen sicher stellt.

Brauchen Sie mehr Informationen? Sehen Sie sich diese Seite an.

Hier können Sie Ihre Cookie-Einstellungen nach Ihren Wünschen anpassen.

Wir benötigen Ihre Einwilligung zur Verwendung der einzelnen Daten, damit Sie unter anderem Informationen zu Ihren Interessen einsehen können.