Cookies
Wir benötigen Ihre Einwilligung zur Verwendung der einzelnen Daten, damit Sie unter anderem Informationen zu Ihren Interessen einsehen können. Klicken Sie auf "OK", um Ihre Zustimmung zu erteilen.
ASTM B395/B395M-08
Standard Specification for U-Bend Seamless Copper and Copper Alloy Heat Exchanger and Condenser Tubes
Automatische name übersetzung:
Standard-Spezifikation für U- Bend- Seamless Kupfer und Kupferlegierungen Wärmetauscher und Kondensatorrohre
NORM herausgegeben am 1.4.2008
Informationen über die Norm:
Bezeichnung normen: ASTM B395/B395M-08
Anmerkung: UNGÜLTIG
Ausgabedatum normen: 1.4.2008
SKU: NS-6533
Zahl der Seiten: 12
Gewicht ca.: 36 g (0.08 Pfund)
Land: Amerikanische technische Norm
Kategorie: Technische Normen ASTM
Die Annotation des Normtextes ASTM B395/B395M-08 :
Keywords:
condenser tube, copper, copper alloy, dual-gage, evaporator, heat exchanger, U-bend tube, C10200, C10300, C10800, C12000, C12200, C14200, C19200, C23000, C44300, C44400, C44500, C60800, C68700, C70400, C70600, C70620, C71000, C71500, C71520, C72200, Aluminum bronzes--specifications, Brass pipe/tube--specifications, Bronze pipe/tube--specifications, Condenser and heat exchanger systems--copper/copper alloy, Seamless Cu/Cu alloy tube--specifications
Ergänzende Informationen
| Significance and Use | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
For purpose of determining compliance
with the specified limits for requirements of the properties listed
in the following table, an observed value or a calculated value
shall be rounded as indicated in accordance with the rounding
method of Practice E 29.
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 1. Scope | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
1.1 This specification establishes the requirements for condenser, evaporator, and heat exchanger U-bend tubes that are manufactured from seamless copper and copper alloy tube. 1.2 The following safety hazard caveat pertains only to the test methods described in this specification. 1.2.1 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use. 1.3 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 This specification is applicable to product 2 in. [50 mm] or less, inclusive, in diameter. 1.5 The product shall be produced from
one of the following coppers or copper alloys, as specified in the
ordering information:
A Designations listed in Classification B 224. |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 2. Referenced Documents | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Empfehlungen:
Aktualisierung der Gesetze
Wollen Sie sich sicher sein, dass Sie nur die gültigen technischen Vorschriften verwenden?
Wir bieten Ihnen Lösungen, damit Sie immer nur die gültigen (aktuellen) legislativen Vorschriften verwenden könnten.
Brauchen Sie mehr Informationen? Sehen Sie sich diese Seite an.
