Vorsicht!

In Ihrem Browser ist die Javascript-Aktivierung nicht erlaubt. Einige Funktionen mögen nicht richtig funktionieren. Für vollständige Funktionalität des Internet-Geschäfts empfehlen wir Javascript zu aktivieren. Siehe hier Instruktion, wie man im Ihren Web-Browser JavaScript aktiviert.

Angezeigte Währung: €

Preisanzeige: ohne MWS

Die Norm ASTM B580-79(2019) 1.4.2019 Ansicht

Ergänzende Informationen

ASTM B580-79(2019)

Standard Specification for Anodic Oxide Coatings on Aluminum

Name übersetzen

NORM herausgegeben am 1.4.2019

Sprache
Realisierung	PDF - sofortiges Download - 51.40 € Gedruckt - 51.40 €
Zugänglichkeit	AUF LAGER
Preis	51.40 € ohne MWS
51.40 €

Informationen über die Norm:

Bezeichnung normen: ASTM B580-79(2019)
Ausgabedatum normen: 1.4.2019
SKU: NS-945898
Zahl der Seiten: 3
Gewicht ca.: 9 g (0.02 Pfund)
Land: Amerikanische technische Norm
Kategorie: Technische Normen ASTM

Drucken

Einem Bekannten abschicken

Anfrage

Kategorie - ähnliche Normen:

Surface treatment

Die Annotation des Normtextes ASTM B580-79(2019) :

This specification covers the requirements for porous oxide coatings deposited by electrolysis on aluminum and aluminum alloy parts. These coatings should have good appearance, abrasion resistance, electrical properties, and protection against corrosion and does not include nonporous barrier layer anodic coatings that are used for electrical capacitors. The basis metals for these coatings should be subjected to mechanical finishing operations, cleaning, and chemical or electrolytic pre-treatments to yield coatings with fine quality and appearance. Anodized parts should be sealed in water or aqueous chemical solutions except when otherwise specified. Each anodic coating should be continuous, smooth, adherent, uniform in appearance, and free of powdery areas (burns, loose films, stains, discolorations, and discontinuities.

Keywords:
ICS Number Code 25.220.20 (Surface treatment)

Ergänzende Informationen

1. Scope

1.1 This specification covers requirements for electrolytically formed porous oxide coatings on aluminum and aluminum alloy parts in which appearance, abrasion resistance, electrical properties, and protection against corrosion are important. Nonporous, barrier layer anodic coatings used for electrical capacitors are not covered. Seven types of coatings as shown in Table 1 are provided. Definitions and typical examples of service conditions are provided in Appendix X1.

Note 1: It is recognized that uses exist in which modifications of the coatings covered by this specification may be required. In such cases the particular properties desired by the purchaser should be the subject of agreement between the purchaser and the manufacturer.

1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

2. Referenced Documents

E429-78(1991)E01	Test Method for Measurement and Calculation of Reflecting Characteristics of Metallic Surfaces Using Integrating Sphere Instruments (Withdrawn 1996)
D658-91	Standard Test Method for Abrasion Resistance of Organic Coatings by Air Blast Abrasive (Withdrawn 1996)
B137-95(2021)	Standard Test Method for Measurement of Coating Mass Per Unit Area on Anodically Coated Aluminum
B136-23	Standard Test Method for Measurement of Stain Resistance of Anodic Coatings on Aluminum
B117-19	Standard Practice for Operating Salt Spray (Fog) Apparatus
B110-45(1973)	Method of Dielectric Strength of Anodically Coated Aluminum (Withdrawn 1981)
MIL-STD-414	Sampling Procedures and Tables for Inspection by Variables for Percent Defective
B602-21	Standard Guide for Attribute Sampling of Metallic and Inorganic Coatings
B538-70	Method of Fact (Ford Anodized Aluminum Corrosion Test) (Withdrawn 1986)
B487-20	Standard Test Method for Measurement of Metal and Oxide Coating Thickness by Microscopical Examination of Cross Section
B457-67(1998)	Standard Test Method for Measurement of Impedance of Anodic Coatings on Aluminum
B244-09(2021)	Standard Test Method for Measurement of Thickness of Anodic Coatings on Aluminum and of Other Nonconductive Coatings on Nonmagnetic Basis Metals with Eddy-Current Instruments
E430-23	Standard Test Methods for Measurement of Gloss of High-Gloss Surfaces by Abridged Goniophotometry
MIL-STD-105	Sampling Procedures and Tables for Inspection by Attributes Available from Standardization Documents Order Desk, Bldg. 4 Section D, 700 Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.
B368-21	Standard Test Method for Copper-Accelerated Acetic Acid-Salt Spray (Fog) Testing (CASS Test)

Empfehlungen:

Aktualisierung der technischen Normen

Wollen Sie sich sicher sein, dass Sie nur die gültigen technischen Normen verwenden?
Wir bieten Ihnen eine Lösung, die Ihnen eine Monatsübersicht über die Aktualität der von Ihnen angewandten Normen sicher stellt.

Brauchen Sie mehr Informationen? Sehen Sie sich diese Seite an.

Hier können Sie Ihre Cookie-Einstellungen nach Ihren Wünschen anpassen.

Wir benötigen Ihre Einwilligung zur Verwendung der einzelnen Daten, damit Sie unter anderem Informationen zu Ihren Interessen einsehen können.