ASTM C1449/C1449M-05..
ASTM C1478-08(2013)..
ASTM C1479-13
ASTM C1479M-13
ASTM C14M-15
ASTM C1504-15
Cookies
Wir benötigen Ihre Einwilligung zur Verwendung der einzelnen Daten, damit Sie unter anderem Informationen zu Ihren Interessen einsehen können. Klicken Sie auf "OK", um Ihre Zustimmung zu erteilen.
ASTM C1103-14
Standard Practice for Joint Acceptance Testing of Installed Precast Concrete Pipe Sewer Lines
Automatische name übersetzung:
Standard Praxis für gemeinsame Abnahmeprüfung der installierten Betonfertigrohrabwasserleitungen
NORM herausgegeben am 15.11.2014
Informationen über die Norm:
Bezeichnung normen: ASTM C1103-14
Anmerkung: UNGÜLTIG
Ausgabedatum normen: 15.11.2014
SKU: NS-9509
Zahl der Seiten: 2
Gewicht ca.: 6 g (0.01 Pfund)
Land: Amerikanische technische Norm
Kategorie: Technische Normen ASTM
Kategorie - ähnliche Normen:
Die Annotation des Normtextes ASTM C1103-14 :
Keywords:
ICS Number Code 23.040.50 (Pipes and fittings of other materials)
Ergänzende Informationen
| Significance and Use | ||||
|
5.1 This is not a routine test. The values recorded are applicable only to the sewer being tested and at the time of testing. |
||||
| 1. Scope | ||||
|
1.1 This practice covers procedures for testing the joints of installed precast concrete pipe sewer lines, when using either air or water under low pressure to demonstrate the integrity of the joint and the construction procedures. This practice is used for testing 27-in. and larger diameter precast concrete sewer lines utilizing rubber gasket sealed joints. Note 1: The user of this practice is advised that methods
described herein may also be used as a preliminary test to enable
the manufacturer or installer to demonstrate the condition of sewer
pipe prior to delivery.
1.2 This practice is the inch-pound companion to Practice C1103M; therefore, no SI equivalents are presented in the practice. Note 2: The owner shall specify the following: who will
conduct, observe, and furnish labor, material, and measuring
devices and pay for the tests; who is responsible for determining
local ground conditions; and whether an air or water test is to be
used.
Note 3: The user of this practice is advised that test
criteria presented in this practice are similar to those in general
use. Pipe shall be accepted by infiltration or exfiltration testing
utilizing Practice C969.
Note 4: Test times tabulated and the rate of air loss in this
practice are based on successful testing of installed pipelines.
However, since air and water have different physical properties,
retests of some pipelines not meeting field air tests have been
successful when tested with water.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautions are given in Section 6. |
||||
| 2. Referenced Documents | ||||
|
Ähnliche Normen:
Historisch
1.12.2014
Historisch
1.7.2013
Historisch
1.2.2013
Historisch
1.2.2013
Historisch
1.1.2015
Historisch
15.1.2015
Empfehlungen:
Aktualisierung der technischen Normen
Wollen Sie sich sicher sein, dass Sie nur die gültigen technischen Normen verwenden?
Wir bieten Ihnen eine Lösung, die Ihnen eine Monatsübersicht über die Aktualität der von Ihnen angewandten Normen sicher stellt.
Brauchen Sie mehr Informationen? Sehen Sie sich diese Seite an.
