Wir benötigen Ihre Einwilligung zur Verwendung der einzelnen Daten, damit Sie unter anderem Informationen zu Ihren Interessen einsehen können. Klicken Sie auf "OK", um Ihre Zustimmung zu erteilen.
Standard Test Method for Flowability and Bearing Area of Chemical-Resistant Polymer Machinery Grouts
Name übersetzen
NORM herausgegeben am 15.12.2018
Bezeichnung normen: ASTM C1339/C1339M-18
Ausgabedatum normen: 15.12.2018
SKU: NS-937103
Zahl der Seiten: 6
Gewicht ca.: 18 g (0.04 Pfund)
Land: Amerikanische technische Norm
Kategorie: Technische Normen ASTM
Manufacturing processes in the rubber and plastics industries
Keywords:
bearing area, chemical-resistant polymer machinery grout, flowability, surface contact,, ICS Number Code 83.020 (Manufacturing processes in the rubber and plastics industries)
Significance and Use |
5.1 Chemical-resistant polymer machinery grouts are used to provide precision support for machinery or equipment. Note 2: The machinery or equipment or support bases or plates,
or combination thereof, are positioned to the precise elevation and
location required. The bases or plates are typically placed on
prepared foundations and supported on temporary shims or support
bolts (jack screws). Forms are installed to contain the flowable
grout. The grout is poured around the perimeter in such a manner as
to allow the grout to flow around and under the equipment base or
plates. The grout subsequently hardens to provide a strong rigid
support layer capable of withstanding the stresses transferred by
the equipment to the foundation. Although the actual machinery base
plate is typically metal and the cover plate in this test uses
acrylic glass, different grouts using acrylic glass cover plates
has proven useful for comparative purposes as described in this
test in laboratory conditions.
5.2 In addition to the required physical properties of the grout, the flow and bearing area achieved are important considerations for effective grout installation. The two characteristics measured by this test method are flow and bearing area. 5.3 The flow test simulates typical application conditions for a flowable polymer machinery grout in a laboratory environment. It may be used to evaluate the suitability of a particular grout for a specific application, to compare the flowability and bearing area of two or more grouts, or to evaluate the effects of formulation changes, temperature, mixing techniques, or other factors on flowability. 5.4 The estimated amount of upper grout surface contact in percent can be used to compare two or more grouts or show the effects of temperature, formulation changes, or other factors on bearing area. A limited set of results using visual guides (see Fig. 1 and Fig. 2) is used to classify the bearing as “high”—greater than 85 %,” “medium—70 to 85 %,” and “low—less than 70 %.” |
1. Scope |
1.1 This test method covers the measure of flowability of chemical-resistant polymer machinery grouts as evaluated in a 50-mm [2-in.] or 25-mm [1-in.] pour thickness in a laboratory setting. The test method provides for the assessment of upper surface plate contact area (bearing area). These grouts will typically be at least two component formulations that may be used for installations where grout thickness will range from 25 to 150 mm [1 to 6 in.] underneath the base or plates being grouted. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
Wollen Sie sich sicher sein, dass Sie nur die gültigen technischen Normen verwenden?
Wir bieten Ihnen eine Lösung, die Ihnen eine Monatsübersicht über die Aktualität der von Ihnen angewandten Normen sicher stellt.
Brauchen Sie mehr Informationen? Sehen Sie sich diese Seite an.
Letzte Aktualisierung: 2024-03-25 (Zahl der Positionen: 2 885 931)
© Copyright 2024 NORMSERVIS s.r.o.