Wir benötigen Ihre Einwilligung zur Verwendung der einzelnen Daten, damit Sie unter anderem Informationen zu Ihren Interessen einsehen können. Klicken Sie auf "OK", um Ihre Zustimmung zu erteilen.
Standard Test Method for True Specific Gravity of Refractory Materials by Gas-Comparison Pycnometer
Automatische name übersetzung:
Standard Test Method for wahre spezifische Gewicht von Feuerfest-Materialien durch Gas-Vergleich Pyknometer
NORM herausgegeben am 1.10.2012
Bezeichnung normen: ASTM C604-02(2012)
Anmerkung: UNGÜLTIG
Ausgabedatum normen: 1.10.2012
SKU: NS-14223
Zahl der Seiten: 3
Gewicht ca.: 9 g (0.02 Pfund)
Land: Amerikanische technische Norm
Kategorie: Technische Normen ASTM
Keywords:
gas comparison pycnometer, hydratable materials, refractory materials, true specific gravity, ICS Number Code 81.080 (Refractories)
Significance and Use | ||||||
4.1 The true specific gravity of a material is the ratio of its true density, determined at a specific temperature, to the true density of water, determined at a specific temperature. Thus, the true specific gravity of a material is a primary property which is related to chemical and mineralogical composition. 4.2 This test method is particularly useful for hydratable materials which are not suitable for test with Test Method C135. 4.3 For refractory raw materials and products the true specific gravity is a useful value for: classification, detecting differences in chemical composition between supposedly like samples, indicating mineralogical phases or phase changes, calculating total porosity when the bulk density is known, and for any other test method that requires this value for the calculation of results. 4.4 This test method is a primary standard method which is suitable for use in specifications, quality control, and research and development. It can also serve as a referee test method in purchasing contracts or agreements. 4.5 Fundamental assumptions inherent in this test method are the following: 4.5.1 The sample is representative of the material in general, 4.5.2 The total sample has been reduced to the particle size specified, 4.5.3 No contamination has been introduced during processing of the sample, 4.5.4 The ignition of the sample has eliminated all free or combined water without inducing sintering or alteration, 4.5.5 An inert gas (helium) has been used in the test, and 4.5.6 The test method has been conducted in a meticulous manner. 4.5.7 Deviation from any of these assumptions negates the usefulness of the results. 4.6 In interpreting the results of this test method it must be recognized that the specified sample particle size is significantly finer than specified for Test Method C135. Even this finer particle size for the sample does not preclude the presence of some closed pores, and the amount of residual closed pores may vary between materials or even between samples of the same or like materials. The values generated by this test method may, therefore, be very close approximations rather than accurate representations of true specific gravities. Thus, comparisons of results should only be judiciously made between like materials tested by this test method or with full recognition of potentially inherent differences between the materials being compared or the test method used. |
||||||
1. Scope | ||||||
1.1 This test method covers the determination of the true specific gravity of solid materials, and is particularly useful for materials that easily hydrate which are not suitable for test with Test Method C135. This test method may be used as an alternate for Test Method C135, Test Method C128, and Test Method C188 for determining true specific gravity. 1.2 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.2.1 Exception—In 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
||||||
2. Referenced Documents | ||||||
|
Historisch
1.12.2013
Historisch
1.9.2010
Historisch
1.3.2009
Historisch
1.3.2012
Historisch
1.5.2011
Historisch
1.9.2013
Wollen Sie sich sicher sein, dass Sie nur die gültigen technischen Normen verwenden?
Wir bieten Ihnen eine Lösung, die Ihnen eine Monatsübersicht über die Aktualität der von Ihnen angewandten Normen sicher stellt.
Brauchen Sie mehr Informationen? Sehen Sie sich diese Seite an.
Letzte Aktualisierung: 2024-05-14 (Zahl der Positionen: 2 898 634)
© Copyright 2024 NORMSERVIS s.r.o.