Wir benötigen Ihre Einwilligung zur Verwendung der einzelnen Daten, damit Sie unter anderem Informationen zu Ihren Interessen einsehen können. Klicken Sie auf "OK", um Ihre Zustimmung zu erteilen.
Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings (Includes all amendments And changes 9/11/2018).
Automatische name übersetzung:
Standard Test Method for Resistance zu Kurzzeit- Hydraulikdruck der Kunststoffrohr , Schläuche und Armaturen
NORM herausgegeben am 15.4.2014
Bezeichnung normen: ASTM D1599-14e1
Anmerkung: UNGÜLTIG
Ausgabedatum normen: 15.4.2014
SKU: NS-586263
Zahl der Seiten: 4
Gewicht ca.: 12 g (0.03 Pfund)
Land: Amerikanische technische Norm
Kategorie: Technische Normen ASTM
Keywords:
burst pressure, plastic fittings, plastic pipe, plastic tubing, short-term hydrostatic pressure,, ICS Number Code 23.040.20 (Plastic pipes), 23.040.45 (Plastic fittings)
Significance and Use | ||||||
4.1 This test method establishes the short-time hydraulic failure pressure of thermoplastic or reinforced thermosetting resin pipe, tubing, or fittings. Data obtained by this test method are of use only in predicting the behavior of pipe, tubing, and fittings under conditions of temperature, time, method of loading, and hoop stress similar to those used in the actual test. They are generally not indicative of the long-term strength of thermoplastic or reinforced thermosetting resin pipe, tubing, and fittings. 4.2 Procurement specifications utilizing this test method may stipulate a minimum and maximum time for failure other than the 60 to 70 s listed in 9.1.3. Either the internal hydraulic pressure or the hoop stress may be listed in the requirements. Note 1: Many thermoplastics give significantly different burst
strengths depending on the time to failure. For instance,
significant differences have been observed between failure times of
65 and 85 s.
4.3 This test method is also used as a short-term pressurization validation procedure, where the specimens are pressurized to a predetermined minimum pressure requirement. |
||||||
1. Scope | ||||||
1.1 This test method covers the determination of the resistance of either thermoplastic or reinforced thermosetting resin pipe, tubing, or fittings to hydraulic pressure in a short time period. Procedure A is used to determine burst pressure of a specimen if the mode of failure is to be determined. Procedure B is used to determine that a specimen complies with a minimum burst requirement. 1.2 This test method is suitable for establishing laboratory testing requirements for quality control purposes or for procurement specifications. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of whoever uses this standard to consult and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
||||||
2. Referenced Documents | ||||||
|
Historisch
1.12.2009
Historisch
1.11.2013
Historisch
1.11.2011
Historisch
1.8.2012
Historisch
1.2.2010
Historisch
1.11.2013
Wollen Sie sich sicher sein, dass Sie nur die gültigen technischen Vorschriften verwenden?
Wir bieten Ihnen Lösungen, damit Sie immer nur die gültigen (aktuellen) legislativen Vorschriften verwenden könnten.
Brauchen Sie mehr Informationen? Sehen Sie sich diese Seite an.
Letzte Aktualisierung: 2024-04-24 (Zahl der Positionen: 2 895 425)
© Copyright 2024 NORMSERVIS s.r.o.