Wir benötigen Ihre Einwilligung zur Verwendung der einzelnen Daten, damit Sie unter anderem Informationen zu Ihren Interessen einsehen können. Klicken Sie auf "OK", um Ihre Zustimmung zu erteilen.
Standard Test Methods for Flash Point of Liquids by Small Scale Closed-Cup Apparatus
Name übersetzen
NORM herausgegeben am 1.6.2020
Bezeichnung normen: ASTM D3278-20
Anmerkung: UNGÜLTIG
Ausgabedatum normen: 1.6.2020
SKU: NS-995298
Zahl der Seiten: 8
Gewicht ca.: 24 g (0.05 Pfund)
Land: Amerikanische technische Norm
Kategorie: Technische Normen ASTM
Keywords:
flash/no flash, flash point, organic peroxides, organic solvents, small scale closed-cup apparatus,
Significance and Use | ||||||||||||
5.1 Flash point is one of the properties used to define the flammability of a liquid. It is used to classify liquids according to their flammability by governmental regulatory agencies. It may also be used to determine the presence of impurities or contaminants in a given liquid, such as the presence of residual solvents in solvent-refined drying oils. See Test Methods D56 and D93 for alternate flash point testing. |
||||||||||||
1. Scope | ||||||||||||
1.1 These test methods cover procedures for determining whether a material does or does not flash at a specified temperature or for determining the lowest finite temperature at which a material does flash when using a small scale closed-cup apparatus.Note 1: Tests at higher or lower temperatures are possible. Note 2: More viscous materials may be tested in accordance
with Annex A4.
Note 3: Organic peroxides may be tested in accordance with
Annex A5, which describes the
applicable safety precautions.
Note 4: The U.S. Department of Labor (OSHA, Hazard
Communications), the U.S. Department of Transportation (RSPA), and
the U.S. Environmental Protection Agency (EPA) have specified Test
Methods D3278 as one of
several acceptable methods for the determination of flash point of
liquids in their regulations.
Note 5: These test methods are similar to International
Standards ISO 3679 and ISO 3680.
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard should be used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions and should not be used to describe or appraise the fire-hazard or fire-risk of materials, products, or assemblies under actual fire conditions. However, results of the test may be used as elements of a fire-hazard or a fire-risk assessment which takes into account all of the factors which are pertinent to an assessment of the fire hazard or fire risk of a particular end use. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||
2. Referenced Documents | ||||||||||||
|
Wollen Sie sich sicher sein, dass Sie nur die gültigen technischen Normen verwenden?
Wir bieten Ihnen eine Lösung, die Ihnen eine Monatsübersicht über die Aktualität der von Ihnen angewandten Normen sicher stellt.
Brauchen Sie mehr Informationen? Sehen Sie sich diese Seite an.
Letzte Aktualisierung: 2024-04-29 (Zahl der Positionen: 2 896 215)
© Copyright 2024 NORMSERVIS s.r.o.