Wir benötigen Ihre Einwilligung zur Verwendung der einzelnen Daten, damit Sie unter anderem Informationen zu Ihren Interessen einsehen können. Klicken Sie auf "OK", um Ihre Zustimmung zu erteilen.
Standard Practice for Performing Accelerated Outdoor Weathering of Factory-Coated Embossed Hardboard Using Concentrated Natural Sunlight and a Soak-Freeze-Thaw Procedure
Automatische name übersetzung:
Standard Praxis für Darstellende Beschleunigte Freibewitterung der Fabrik-Coated Geprägte Hartfaserplatte Mit konzentrierte natürliche Sonnenlicht und Tränken-Frieren-Tauwetter Vorgehens
NORM herausgegeben am 1.12.2014
Bezeichnung normen: ASTM D5722-14
Anmerkung: UNGÜLTIG
Ausgabedatum normen: 1.12.2014
SKU: NS-579632
Zahl der Seiten: 3
Gewicht ca.: 9 g (0.02 Pfund)
Land: Amerikanische technische Norm
Kategorie: Technische Normen ASTM
Keywords:
accelerated weathering, factory coatings (hardboard), film integrity, hardboard (composition board siding),, ICS Number Code 79.060.20 (Fibre and particle boards)
Significance and Use | ||||||||||||||||
5.1 The ability to quickly and accurately evaluate and predict long-term weathering performance of factory-applied coatings is of paramount importance in making sound business and technical decisions. 5.2 It is important to include control specimens of known field performance to determine the efficacy of this practice for specific substrate(s) and coating system(s). These control specimens may include materials known to possess acceptable and unacceptable field performance for the defect(s) under consideration. 5.3 Results derived from this practice are best used to compare the relative performance of materials tested at the same time in the same device. 5.4 The inclusion of control specimens and their resulting data will assist in dealing with test variability caused by seasonal or annual variations in important climatic factors. 5.5 Extensive research was performed during the development of this standard practice. This research showed that this practice is not useful for determination of quantitative acceleration factors. However, this test is very useful as a comparative test. 5.6 A minimum of two replicates for both control specimens and test specimens is recommended to allow statistical evaluation of results. Refer to Practice G169 for additional guidance on establishing the number of replicates. |
||||||||||||||||
1. Scope | ||||||||||||||||
1.1 This practice covers techniques to accelerate weathering effects of factory-coated embossed hardboard using Cycle 1 of Practice G90 (concentrated natural sunlight with periodic surface water spray) plus a soak-freeze thaw cycle (see Section 5 of this practice). 1.2 Testing by use of the methods described in this practice may be employed in the qualitative assessment of weathering effects. The relative durability of coated hardboards may be best determined by comparison of their test results with those of control specimens derived from real time exposure test experience. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
||||||||||||||||
2. Referenced Documents | ||||||||||||||||
|
Wollen Sie sich sicher sein, dass Sie nur die gültigen technischen Normen verwenden?
Wir bieten Ihnen eine Lösung, die Ihnen eine Monatsübersicht über die Aktualität der von Ihnen angewandten Normen sicher stellt.
Brauchen Sie mehr Informationen? Sehen Sie sich diese Seite an.
Letzte Aktualisierung: 2024-05-05 (Zahl der Positionen: 2 897 047)
© Copyright 2024 NORMSERVIS s.r.o.