Wir benötigen Ihre Einwilligung zur Verwendung der einzelnen Daten, damit Sie unter anderem Informationen zu Ihren Interessen einsehen können. Klicken Sie auf "OK", um Ihre Zustimmung zu erteilen.
Standard Test Method for Determining Automotive Engine Oil Compatibility with Typical Seal ElastomersName übersetzen
NORM herausgegeben am 1.4.2022
Bezeichnung normen: ASTM D7216-22
Ausgabedatum normen: 1.4.2022
Zahl der Seiten: 14
Gewicht ca.: 42 g (0.09 Pfund)
Land: Amerikanische technische Norm
Kategorie: Technische Normen ASTM
automotive engine oil, compatibility, elastomer, engine oil, immersion, seal(s),, ICS Number Code 75.100 (Lubricants, industrial oils and related products)
|Significance and Use|
5.1Some engine oil formulations have been shown to lack compatibility with certain elastomers used for seals in automotive engines. These deleterious effects on the elastomer are greatest with new engine oils (that is, oils that have not been exposed to an engines operating environment) and when the exposure is at elevated temperatures.
5.2This test method requires that non-reference oil(s) be tested in parallel with a reference oil known to be aggressive for some parameters under service conditions. This relative compatibility permits decisions on the anticipated or predicted performance of the non-reference oil in service.
5.3Elastomer materials can show significant variation in physical properties, not only from batch to batch but also within a sheet and from sheet to sheet. Results obtained with the reference oil are submitted by the test laboratories to the TMC to allow it to update continually the total and within-laboratory standard deviation estimates. These estimates, therefore, incorporate effects of variations in the properties of the reference elastomers on the test variability.
5.4This test method is suitable for specification compliance testing, quality control, referee testing, and research and development.
5.5The reference elastomers, reference oil, and the physical properties involved in this test method address the specific requirements of engine oils. Although other tests exist for compatibility of elastomers with liquids, these are considered too generalized for engine oils.
1.1This test method covers quantitative procedures for the evaluation of the compatibility of automotive engine oils with several reference elastomers typical of those used in the sealing materials in contact with these oils. Compatibility is evaluated by determining the changes in volume, Durometer A hardness, and tensile properties when the elastomer specimens are immersed in the oil for a specified time and temperature.
1.2Effective sealing action requires that the physical properties of elastomers used for any seal have a high level of resistance to the liquid or oil in which they are immersed. When such a high level of resistance exists, the elastomer is said to be compatible with the liquid or oil.
Note 1:The user of this test method should be proficient in the use of Test Methods (tensile properties), (effect of rubber immersion in liquids), (Durometer hardness), and (gear oil compatibility with typical oil seal elastomers), all of which are involved in the execution of the operations of this test method.
1.3This test method provides a preliminary or first order evaluation of oil/elastomer compatibility only. Because seals might be subjected to static or dynamic loads, or both, and they can operate over a range of conditions, a complete evaluation of the potential sealing performance of any elastomer-oil combination in any service condition usually requires tests additional to those described in this test method.
1.4The several reference elastomer formulations specified in this test method were chosen to be representative of those used in both heavy-duty diesel engines (detailed in ) and passenger-car spark-ignition engines (the latter are covered in ). The procedures described in this test method can, however, also be used to evaluate the compatibility of automotive engine oils with different elastomer types/formulations or different test durations and temperatures to those employed in this test method.
Note 2:In such cases, the precision and bias statement in Section (1) test temperatures and immersion times to be used; Note 3:The TMC may also issue Information Letters on this matter. does not apply. In addition to agreeing acceptable limits of precision, where relevant, the user and supplier should also agree:
1.5The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.6This test method is arranged as follows:
1.7This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.8This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
|2. Referenced Documents|
Bereitstellung von aktuellen Informationen über legislative Vorschriften in der Sammlung der Gesetze bis zum Jahr 1945.
Aktualisierung 2x pro Monat!
Brauchen Sie mehr Informationen? Sehen Sie sich diese Seite an.
Letzte Aktualisierung: 2023-02-07 (Zahl der Positionen: 2 663 633)
© Copyright 2023 NORMSERVIS s.r.o.