Standard Test Methods for Determining Loose and Tapped Bulk Densities of Powders using a Graduated CylinderName übersetzen
NORM herausgegeben am 1.6.2018
Bezeichnung normen: ASTM D7481-18
Ausgabedatum normen: 1.6.2018
Zahl der Seiten: 4
Gewicht ca.: 12 g (0.03 Pfund)
Land: Amerikanische technische Norm
Kategorie: Technische Normen ASTM
loose bulk density, tapped bulk density,, ICS Number Code 17.060 (Measurement of volume, mass, density, viscosity)
|Significance and Use|
5.1 The data from the loose bulk density test can be used to estimate the size of bags, totes, small bins or hoppers for the storage of a fixed mass of powder in its loose condition. It can also be used to estimate the mass of powder that will fit in small size containers such as drums. It cannot be used to estimate powder quantities of large vessels such as silos.
5.2 Values of loose bulk density obtained using this test method should be used with caution, since they can vary considerably depending on the inital state of dispersion of the test specimen, height-to-diameter ratio of specimen in graduated cylinder, dryness of powder, and other factors.
5.3 The data from the tapped bulk density test can be used to estimate the needed volume of small containers holding a fixed mass of powder that has been compacted. An example would be a packing line where vibration is used to tamp powders into a small container for effective packing purposes.
5.4 Bulk density values can vary significantly if the particle size of the actual material to be handled is different than tested. A bulk solid consisting of large and small particles often has higher bulk densities than the fine particles by themselves. For powders, lower densities are possible if the fine particles are fluidized or aerated.
5.5 The results of this test method are most applicable to containers with volumes up to about one cubic meter. Another method (such as ) should be used when considering larger silos.
Note 1: The quality of the results produced by this standard is dependent on the competence of the personnel performing it, and the suitability of the equipment and facilities used. Agencies that meet the criteria of Practice are generally considered capable of competent and objective testing/sampling/inspection/etc. Users of this standard are cautioned that compliance with Practice does not in itself assure reliable results. Reliable results depend on many factors; Practice provides a means of evaluating some of those factors. Practice was developed for agencies engaged in the testing or inspection (or both) of soil and rock. As such it is not totally applicable to agencies performing this standard. However, users of this standard should recognize that the framework of Practice is appropriate for evaluating the quality of an agency performing this standard. Currently there is no known qualifying national authority that inspects agencies that perform this standard.
1.1 This test method covers the apparatus and procedures for determining the bulk densities of free flowing and moderately cohesive powders and granular materials up to 3.5 mm in size in their loose (Method A) and tapped (Method B) states.
1.2 This test method should be performed in a laboratory under controlled conditions of temperature and humidity.
1.3 This test method is similar to those of Test Methods , , , , and .
1.4 All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice .
1.4.1 The procedures used to specify how data are collected/recorded or calculated in this standard are regarded as the industry standard. In addition they are representative of the significant digits that generally should be retained. The procedures used do not consider material variations, purpose for obtaining the data, special purpose studies, or any considerations for the user’s objectives; and it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations. It is beyond the scope of this standard to consider significant digits used in analysis methods for engineering design.
1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
|2. Referenced Documents|
Wollen Sie sich sicher sein, dass Sie nur die gültigen technischen Normen verwenden?
Wir bieten Ihnen eine Lösung, die Ihnen eine Monatsübersicht über die Aktualität der von Ihnen angewandten Normen sicher stellt.
Brauchen Sie mehr Informationen? Sehen Sie sich diese Seite an.
Letzte Aktualisierung: 2021-09-17 (Zahl der Positionen: 2 524 940)
© Copyright 2021 NORMSERVIS s.r.o.