Standard Test Method for Torsional Ring Shear Test to Measure Drained Fully Softened Shear Strength and Stress Dependent Strength Envelope of Fine-Grained SoilsName übersetzen
NORM herausgegeben am 1.6.2018
Bezeichnung normen: ASTM D7608-18
Ausgabedatum normen: 1.6.2018
Zahl der Seiten: 6
Gewicht ca.: 18 g (0.04 Pfund)
Land: Amerikanische technische Norm
Kategorie: Technische Normen ASTM
consolidated, drained test conditions, fully softened shear strength, reconstituted specimens, ring-shear test, slope stability, strength envelope,, ICS Number Code 13.080.20 (Physical properties of soil)
|Significance and Use|
5.1 The ring shear apparatus maintains the cross-sectional area of the shear surface constant during shear and shears the specimen continuously in one rotational direction for any magnitude of shear displacement and along the entire specimen cross-sectional area.
5.2 The ring shear apparatus allows a reconstituted specimen to be consolidated at the desired normal stress prior to drained shearing. This simulates the field conditions under which complete softening develops in overconsolidated clays, claystones, mudstones, and shales that do not have a pre-existing shear surface, sheared bedding planes, joints, or faults as described by Skempton (1970 and 19775.3 The ring shear test is suited to the determination of the drained fully softened shear strength because of the short drainage path through the thin specimen, small post-peak strength loss in a normally consolidated specimen, and the constant cross-sectional area.
5.4 The ring shear test specimen is annular so the angular displacement differs from the inner radius to the outer radius. This is not significant because a normally consolidated specimen does not exhibit a large post-peak strength loss so the difference in peak shear resistance at the inner radius and outer radius at different displacements is not significant and the ratio of the inner to outer radii of the ring is greater than 0.5 in accordance with Hvorslev (1936)Note 1: Notwithstanding the statements on precision and bias contained in this test method: The precision of this test method is dependent on the competence of the personnel performing it and the suitability of the equipment and facilities used. Agencies that meet the criteria of Practice are generally considered capable of competent testing. Users of this test method are cautioned that compliance with Practice does not ensure reliable testing. Reliable testing depends on several factors; Practice provides a means of evaluating some of those factors.
1.1 This test method provides a procedure for performing a torsional ring shear test under a drained condition to measure the fully softened shear strength and stress dependent strength envelope of fine-grained soils (using a reconstituted normally consolidated specimen). The fully softened strength and the corresponding stress dependent effective stress strength envelope are used to evaluate the stability of slopes that do not have a pre-existing shear surface but have been subjected to environmental conditions and shear stresses that lead to soil softening, deterioration of the soil fabric, and strength loss. It has been shown (Skempton 1970 and 19771.2 The ring shear apparatus allows a reconstituted specimen to be normally consolidated at the desired normal stress prior to drained shearing. The test results closely simulate the fully softened strength of stiff natural fine-grained soils (Skempton 19701.3 A shear stress-displacement relationship may be obtained from this test method. However, a shear stress-strain relationship or any associated quantity, such as modulus, cannot be determined from this test method because defining the height of the shear zone is difficult and needed in the shear strain calculations. As a result, the height of this shear zone is unknown, so an accurate or representative shear strain can therefore not be determined.
1.4 The selection of normal stresses and final determination of the shear strength envelope for design analyses and the criteria to interpret and evaluate the test results are the responsibility of the engineer or entity requesting the test.
1.5 Units—The values stated in SI units are to be regarded as the standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
|2. Referenced Documents|
Letzte Aktualisierung: 2021-09-17 (Zahl der Positionen: 2 524 940)
© Copyright 2021 NORMSERVIS s.r.o.