Standard Guide for Placement of Intentional Leaks During Electrical Leak Location Surveys of Geomembranes (Includes all amendments and changes 5/6/2021).Name übersetzen
NORM herausgegeben am 1.5.2021
Bezeichnung normen: ASTM D7909-21a
Ausgabedatum normen: 1.5.2021
Zahl der Seiten: 5
Gewicht ca.: 15 g (0.03 Pfund)
Land: Amerikanische technische Norm
Kategorie: Technische Normen ASTM
blind leak, electrical leak location, geomembrane, known leak, leak detection, leak location,, ICS Number Code 59.080.70 (Geotextiles)
|Significance and Use|
4.1Geomembranes are used as low-permeability barriers to control liquids from leaking from landfills, ponds, and other containments. The liquids may contain contaminants that, if released, can cause damage to the environment. Leaking liquids can also erode the subgrade. Leakage can result in product loss or otherwise prevent the installation from performing its intended containment purpose. For these reasons, it is desirable that the geomembrane have as little leakage as practical.
4.2Geomembrane leaks can result even when the quality of the subgrade preparation, the quality of the material placed on the geomembrane, and the quality of the workmanship are not deficient.
4.3Electrical leak location methods are an effective final quality assurance (QA) measure to locate previously undetected leaks in electrically insulating geomembranes. Practices for these implementations are contained in Guide and Practices , , , , , and .
4.4It is important to realize that the detection of leaks depends not only on the capabilities of the leak location equipment, procedures, and experience of the leak location practitioner, but also on local site conditions that are not under the control of the leak location practitioner. In particular, to detect a leak, there shall be an electrical conduction path through the leak and through the materials above and below the leak to allow sufficient electrical current through the leak for detection. Some site conditions, such as a leak not making contact with the subgrade, dry geotextile, or geocomposite above or below the leak; dry materials above or below the leak; degree of isolation between the materials above and below the geomembrane; and other factors, may preclude the detection of leaks. Therefore, the use of a properly placed leak is also a test of site preparations and conditions.
4.5It is not necessarily proper to conclude that, if a leak is not detected, a leak location survey using the proper relevant ASTM International standard has no validity. Other leaks that have more favorable local conditions and larger leaks may still be detected.
4.6The importance of blind leaks is to provide an additional measure to assess whether the site conditions throughout the entire survey area are proper for a leak location survey and that the electric leak location survey is performed correctly and completely. The use of blind leaks provides: (1) a check that the equipment is operating properly, (2) a test for proper survey coverage, and (4.7The placement of blind leaks should not replace hiring a reputable and qualified leak location practitioner to perform the electrical leak location survey. Many site-specific issues and technical limitations can preclude the detection of leaks, but a non-expert will find it difficult to impossible to determine whether the non-detection of leaks is due to survey performance errors or issues with site conditions. It is therefore important to achieve a satisfactory resolution to any issues with the non-detection of leaks but, much more importantly, to check leak location practitioner references and qualifications before hiring. In addition to checking references from previous clients, qualifications should include reports from at least three projects completed, similar in cross section to the proposed project, where leaks were found. The report output should provide indisputable evidence that the survey was performed effectively.
4.8It is important to note that the placement of leaks may affect the sensitivity of the electrical leak location survey for geomembranes covered with soil or water or both. The placement of leaks larger than the leaks present in the lining system may preclude detection of those smaller leaks, especially for highly conductive cover materials.
1.1This guide is for placing leaks in geomembranes before performing an electrical leak location survey. The geomembranes can be bare (not covered) or can be covered with water or moist soil.
1.2This guide is intended to serve as an additional quality control/quality assurance (QC/QA) measure to ensure that leaks through the geomembrane are detectable, site conditions are proper for leak location surveys, and a valid and complete leak location survey is performed. Because various leak location practitioners use a wide variety of equipment to perform these surveys and have a wide range of expertise, placement of leaks by the owner or owners representative helps ensure that the leak location survey is being performed correctly and completely.
1.3Placing leaks should be done with the consent and knowledge of all involved parties and specifically the owner of the geomembrane. Geomembranes are typically purchased and installed by dedicated geosynthetic installers who own the geomembrane until the ownership gets transferred to the end user. A project meeting should be set up with the owner, the consultant, the geosynthetic installers, and the leak location contractor. The intention to create leaks should be clearly stated by the owner or consultants or both, and the scope and number to be placed should be understood by all parties. The consultant should broadly identify to the lining contractor a location that can be easily repaired after the test. It is critical that all leaks be included on the liner documentation and repair record drawing.
1.4Leak location surveys can be used on geomembranes installed in basins, ponds, tanks, ore and waste pads, landfill cells, landfill caps, and other containment facilities. The procedures are applicable for geomembranes made of electrically insulating materials. (WarningThe electrical methods used for geomembrane leak location could use high voltages, resulting in the potential for electrical shock or electrocution. This hazard might be increased because operations might be conducted in or near water. In particular, a high voltage could exist between the water or earth material and earth ground or any grounded conductor. These procedures are potentially very dangerous and can result in personal injury or death. The electrical methods used for geomembrane leak location should be attempted only by qualified and experienced personnel. Appropriate safety measures shall be taken to protect the leak location operators as well as other people at the site.)
1.5The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.7This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
|2. Referenced Documents|
Wollen Sie sich sicher sein, dass Sie nur die gültigen technischen Normen verwenden?
Wir bieten Ihnen eine Lösung, die Ihnen eine Monatsübersicht über die Aktualität der von Ihnen angewandten Normen sicher stellt.
Brauchen Sie mehr Informationen? Sehen Sie sich diese Seite an.
Letzte Aktualisierung: 2021-09-25 (Zahl der Positionen: 2 527 132)
© Copyright 2021 NORMSERVIS s.r.o.