Standard Test Method for Determining Mass per Unit Area of Geohazard NettingsName übersetzen
NORM herausgegeben am 1.9.2021
Bezeichnung normen: ASTM D8122-21
Ausgabedatum normen: 1.9.2021
Zahl der Seiten: 3
Gewicht ca.: 9 g (0.02 Pfund)
Land: Amerikanische technische Norm
Kategorie: Technische Normen ASTM
geohazard netting, mass per unit area,
|Significance and Use|
5.1Using a geohazard netting as a medium to retain rock particles necessitates compatibility between it and the adjacent rock. This test method measures the mass per unit area of a geohazard netting which is often specified by design engineers as an indicator of a geohazard nettings ability to stabilize and control the movement of loose rocks. Knowing a geohazard nettings mass per unit area is also important in analyzing the anchoring required to support the mesh at the top of a soil or rock slope.
5.2This test method may also be used for quality control during the manufacturing process and quality assurance that material meets project or material specifications.
Note 1:The quality of the result produced by this standard is dependent on the competence of the personnel performing it, and the suitability of the equipment and facilities used. Agencies that meet the criteria of Practice are generally considered capable of competent and objective testing/sampling/inspection/etc. Users of this standard are cautioned that compliance with Practice does not in itself assure reliable results. Reliable results depend on many factors; Practice provides a means of evaluating some of those factors.
1.1This test method is an index test to determine the mass per unit area of geohazard nettings. The mass per unit area is a characteristic of a geohazard netting that contributes to its ability to stabilize and control the movement of loose rocks. There are many different types of geohazard nettings which necessitates a single standard by which all geohazard nettings may be measured.
1.2UnitsThe values stated in SI units are to be regarded as standard. The values given in parentheses are provided for information only and are not considered standard. Reporting of test results in units other than SI shall not be regarded as nonconformance with this standard.
1.2.1It is common practice in the engineering/construction profession to concurrently use pounds to represent both a unit of mass (lbm) and of force (lbf). This practice implicitly combines two separate systems of units; the absolute and the gravitational systems. It is scientifically undesirable to combine the use of two separate sets of inch-pound units within a single standard. As stated, this standard includes the gravitational system of inch-pound units and does not use/present the slug unit of mass. However, the use of balances and scales recording pounds of mass (lbm) or recording density in lbm/ft3 shall not be regarded as nonconformance with this standard.
1.2.2The terms density and unit weight are often used interchangeably. Density is mass per unit volume, whereas, unit weight is force per unit volume. In this standard, density is given only in SI units. After the density has been determined, the unit weight is calculated in SI or inch-pound units, or both.
1.3All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice , unless superseded by this test method.
1.3.1The procedures used to specify how data are collected/recorded and calculated in the standard are regarded as the industry standard. In addition, they are representative of the significant digits that generally should be retained. The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the users objectives; and it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations. It is beyond the scope of these test methods to consider significant digits used in analysis methods for engineering data.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Wollen Sie sich sicher sein, dass Sie nur die gültigen technischen Normen verwenden?
Wir bieten Ihnen eine Lösung, die Ihnen eine Monatsübersicht über die Aktualität der von Ihnen angewandten Normen sicher stellt.
Brauchen Sie mehr Informationen? Sehen Sie sich diese Seite an.
Letzte Aktualisierung: 2021-09-21 (Zahl der Positionen: 2 526 736)
© Copyright 2021 NORMSERVIS s.r.o.