Cookies
Wir benötigen Ihre Einwilligung zur Verwendung der einzelnen Daten, damit Sie unter anderem Informationen zu Ihren Interessen einsehen können. Klicken Sie auf "OK", um Ihre Zustimmung zu erteilen.
ASTM D8322-20
Standard Test Method for Determination of Elements in Residual Fuels and Crude Oils by Microwave Plasma Atomic Emission Spectroscopy (MP-AES)
Name übersetzen
NORM herausgegeben am 1.6.2020
Informationen über die Norm:
Bezeichnung normen: ASTM D8322-20
Anmerkung: UNGÜLTIG
Ausgabedatum normen: 1.6.2020
SKU: NS-997648
Zahl der Seiten: 11
Gewicht ca.: 33 g (0.07 Pfund)
Land: Amerikanische technische Norm
Kategorie: Technische Normen ASTM
Die Annotation des Normtextes ASTM D8322-20 :
Keywords:
calcium, crude oil, emission-spectrometry, iron, microwave plasma atomic emission spectroscopy, MP-AES, nickel, potassium, sodium, vanadium,, ICS Number Code 75.160.01 (Fuels in general)
Ergänzende Informationen
| Significance and Use | |
|
5.1 This test method covers the determination of V, Ni, Ca, Na, Al, Si, Zn, P, and S for residual fuels and Fe, V, Ni,Ca, Na, K, and S for crude oils. This test method complements and extends the capabilities of Test Methods D1548 and D5708, which only apply to the determination of Ni, V, and Fe in crude oils and residual fuels. 5.2 The metals and other elements tested for in this method may occur naturally or may be added as a result of production (that is, catalyst fines). |
|
| 1. Scope | |
|
1.1 This test method covers the determination of metals and other elements in residual fuel and crude oil by microwave plasma atomic emission spectroscopy (MP-AES). The specific elements within the scope of this method are V, Ni, Ca, Na, Al, Si, Zn, P, and S for residual fuel oil and Fe, V, Ni, Ca, Na, K, and S for crude oils. 1.2 Method working range: (1) lowest ILS sample mean − R(2) X − R Crude Oil: |
|
|
Element |
Method Working Range |
|
(expected mg/kg) |
|
|
Iron |
0.70 to 161.02 |
|
Vanadium |
2.88 to 417.50 |
|
Nickel |
0.36 to 107.66 |
|
Calcium |
5.41 to 96.78 |
|
Sodium |
1.18 to 97.13 |
|
Potassium |
7.01 to 63.83 |
|
Sulfur |
1059 to 35194 |
|
Residual Fuel Oil: |
|
|
Element |
Method Working Range |
|
(expected mg/kg) |
|
|
Vanadium |
3.88 to 370.09 |
|
Nickel |
1.47 to 96.68 |
|
Calcium |
4.41 to 102.01 |
|
Sodium |
2.80 to 112.67 |
|
Aluminum |
4.13 to 154.12 |
|
Silicon |
5.99 to 237.56 |
|
Zinc |
2.75 to 102.46 |
|
Sulfur |
1314 to 30134 |
1.3 This test method uses soluble metals in organic solvents for calibration and does not purport to quantitatively determine insoluble particulates. Analytical results are particle size dependent, and particles larger than a few micrometers may cause results to appear low
1.4 Elements present at mass fractions above the upper limit of the calibration curves can be determined with additional appropriate dilutions. Elements shall be measured at the wavelengths presented in Table 1.
1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
