Cookies
Wir benötigen Ihre Einwilligung zur Verwendung der einzelnen Daten, damit Sie unter anderem Informationen zu Ihren Interessen einsehen können. Klicken Sie auf "OK", um Ihre Zustimmung zu erteilen.
ASTM E3090/E3090M-17
Standard Test Methods for Strength Properties of Metal Ceiling Suspension Systems
Name übersetzen
NORM herausgegeben am 1.4.2017
Informationen über die Norm:
Bezeichnung normen: ASTM E3090/E3090M-17
Anmerkung: UNGÜLTIG
Ausgabedatum normen: 1.4.2017
SKU: NS-680814
Zahl der Seiten: 9
Gewicht ca.: 27 g (0.06 Pfund)
Land: Amerikanische technische Norm
Kategorie: Technische Normen ASTM
Kategorie - ähnliche Normen:
Die Annotation des Normtextes ASTM E3090/E3090M-17 :
Keywords:
ceiling suspension mechanical properties, connection strength in compression, connection strength in tension, load carrying capacity,, ICS Number Code 91.120.20 (Acoustics in building. Sound insulation)
Ergänzende Informationen
| Significance and Use | ||||||||||
|
4.1 Load Carrying Capacity: 4.1.1 Most architectural specifications contain a uniform load requirement based on Specification C635. Additionally, it is useful to know the uniform loads of cross runners to evaluate their suitability for various ceiling loads. 4.1.2 The procedure detailed in this standard is intended to be used for the simple four foot span specified in Specification C635. It can be used for simple spans other than four feet, but an engineering analysis is required to determine the proper spacing of concentrated loads necessary to simulate a uniform load. 4.1.3 Various concentrated load combinations can be similarly tested or they can be calculated from the uniform load results by engineering analysis. 4.2 Connection Strength in Tension and Compression: 4.2.1 Structural failure of grid systems under axial loading is controlled by the failure of connections between the grid members. Specification of the allowable axial loads is useful for designers and specifiers for determining which grid systems will be appropriate for specific job conditions. 4.2.2 Connection strength is particularly important where the grid installation is expected to experience lateral loads due to earthquake or wind. 4.2.3 Connection strength in both compression and in tension are specified in Practice E580 as mean ultimate test load in tension and in compression. |
||||||||||
| 1. Scope | ||||||||||
|
1.1 These test methods cover metal ceiling suspension systems used primarily to support acoustical tile, acoustical lay-in panels, or suspended T-bar type ceiling systems. 1.2 These test methods cover the determination of strength properties of suspended ceiling grid system components as follows:
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 The following safety hazards caveat pertains only to the test methods described in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||
Empfehlungen:
Aktualisierung der technischen Normen
Wollen Sie sich sicher sein, dass Sie nur die gültigen technischen Normen verwenden?
Wir bieten Ihnen eine Lösung, die Ihnen eine Monatsübersicht über die Aktualität der von Ihnen angewandten Normen sicher stellt.
Brauchen Sie mehr Informationen? Sehen Sie sich diese Seite an.
