Die Annotation des Normtextes ASTM E458-08(2015) :
Keywords: ablation, cold-wall heat of ablation, effective heat of ablation, heat of ablation, thermochemical heat of ablation ,, ICS Number Code 17.200.10 (Heat. Calorimetry)
Ergänzende Informationen
Significance and Use
4.1General—The heat of ablation provides a
measure of the ability of a material to serve as a heat protection
element in a severe thermal environment. The parameter is a
function of both the material and the environment to which it is
subjected. It is therefore required that laboratory measurements of
heat of ablation simulate the service environment as closely as
possible. Some of the parameters affecting the heat of ablation are
pressure, gas composition, heat transfer rate, mode of heat
transfer, and gas enthalpy. As laboratory duplication of all
parameters is usually difficult, the user of the data should
consider the differences between the service and the test
environments. Screening tests of various materials under simulated
use conditions may be quite valuable even if all the service
environmental parameters are not available. These tests are useful
in material selection studies, materials development work, and many
other areas.
4.2Steady-State Conditions—The nature of the
definition of heat of ablation requires steady-state conditions.
Variances from steady-state may be required in certain
circumstances; however, it must be realized that transient
phenomena make the values obtained functions of the test duration
and therefore make material comparisons difficult.
4.2.1Temperature Requirements—In a
steady-state condition, the temperature propagation into the
material will move at the same velocity as the gas-ablation surface
interface. A constant distance is maintained between the ablation
surface and the isotherm representing the temperature front. Under
steady-state ablation the mass loss and length change are linearly
related.
4.2.2Exposure Time Requirements—The exposure
time required to achieve steady-state may be determined
experimentally by the use of multiple models by plotting the total
mass loss as a function of the exposure time. The point at which
the curve departs significantly from linearity is the minimum
exposure time required for steady-state ablation to be established.
Cases exist, however, in the area of very high heating rates and
high shear where this type of test for steady-state may not be
possible.
1. Scope
1.1 This test method covers determination
of the heat of ablation of materials subjected to thermal
environments requiring the use of ablation as an energy dissipation
process. Three concepts of the parameter are described and defined:
cold wall, effective, and thermochemical heat of ablation.
1.2This standard does not purport to
address all of the safety concerns, if any, associated with its
use. It is the responsibility of the user of this standard to
establish appropriate safety and health practices and determine the
applicability of regulatory limitations prior to use.
Wir benötigen Ihre Einwilligung zur Verwendung der einzelnen Daten, damit Sie unter anderem Informationen zu Ihren Interessen einsehen können. Klicken Sie auf "OK", um Ihre Zustimmung zu erteilen.
Hier können Sie Ihre Cookie-Einstellungen nach Ihren Wünschen anpassen.
Technische Cookies
Diese Cookies sind für das ordnungsgemäße Funktionieren der Website und aller Funktionen, die die Website bietet, unerlässlich. Technische Cookies können nicht deaktiviert werden, da sie für das Speichern von Produkten im Warenkorb, das Einrichten von Filtern, das Durchführen des Einkaufsvorgangs, die Favoritenliste und die Datenschutzeinstellungen verantwortlich sind.
Analytische Cookies ermöglichen es uns, die Leistung unserer Website und unserer Werbekampagnen zu messen. Sie werden verwendet, um die Anzahl der Besuche und die Quellen der Besuche auf unserer Website zu ermitteln. Wir verarbeiten die durch diese Cookies gewonnenen Daten summarisch, ohne Verwendung von Kennungen, die auf bestimmte Benutzer unserer Website verweisen. Wenn Sie die Verwendung von Analyse-Cookies in Bezug auf Ihren Besuch deaktivieren, verlieren wir die Möglichkeit, die Leistung zu analysieren und unsere Aktionen zu optimieren.
Wir verwenden Cookies und andere Technologien auch, um unser Geschäft auf die Bedürfnisse und Interessen unserer Kunden auszurichten und Ihnen ein außergewöhnliches Einkaufserlebnis zu bereiten.
Durch die Verwendung personalisierter Cookies können wir die Erklärung unerwünschter Informationen, wie beispielsweise unangemessene Produktempfehlungen oder nutzlose Sonderangebote, vermeiden. Darüber hinaus ermöglicht uns der Einsatz personalisierter Cookies, Ihnen zusätzliche Funktionen anzubieten, wie zum Beispiel auf Ihre Bedürfnisse zugeschnittene Produktempfehlungen.
Werbe-Cookies werden von uns oder unseren Partnern verwendet, damit wir sowohl auf unserer Website als auch auf den Websites Dritter passende Inhalte oder Werbung anzeigen können. Dadurch können wir auf Grundlage Ihrer Interessen Profile erstellen, sogenannte pseudonymisierte Profile. Anhand dieser Informationen ist es in der Regel nicht möglich, Sie sofort zu identifizieren, da ausschließlich pseudonymisierte Daten verwendet werden. Wenn Sie nicht einverstanden sind, werden Sie nicht der Empfänger von Inhalten und Anzeigen, die auf Ihre Interessen zugeschnitten sind.