Standard Guide for Neutron Irradiation of Unbiased Electronic ComponentsName übersetzen
NORM herausgegeben am 1.3.2018
Bezeichnung normen: ASTM F1190-18
Ausgabedatum normen: 1.3.2018
Zahl der Seiten: 6
Gewicht ca.: 18 g (0.04 Pfund)
Land: Amerikanische technische Norm
Kategorie: Technische Normen ASTM
dosimetry, electronic component, equivalent monoenergetic neutron fluence, fast burst reactor (FBR), gallium arsenide, gamma dose, gamma effects, irradiation, neutron fluence, neutron flux, nickel, 1 MeV equivalent fluence, radiation, reactor, semiconductor, silicon, sulfur, thermoluminescent dosimeter (TLD), TRIGA-type reactor,, ICS Number Code 31.020 (Electronic components in general), 31.080.01 (Semi-conductor devices in general)
|Significance and Use|
5.1 Semiconductor devices can be permanently damaged by neutrons (5.2 This guide provides a method by which the exposure of silicon and gallium arsenide semiconductor devices to neutron irradiation may be performed in a manner that is repeatable and which will allow comparison to be made of data taken at different facilities.
5.3 For semiconductors other than silicon and gallium arsenide, applicable validated 1-MeV damage functions are not available in codified National standards. In the absence of a validated 1-MeV damage function, the non-ionizing energy loss (NIEL) or the displacement kerma, as a function of incident neutron energy, normalized to the response in the 1 MeV energy region, may be used as an approximation. See Practice for a description of the method used to determine the damage functions in Si and GaAs ().
1.1 This guide strictly applies only to the exposure of unbiased silicon (Si) or gallium arsenide (GaAs) semiconductor components (integrated circuits, transistors, and diodes) to neutron radiation to determine the permanent damage in the components. Validated 1-MeV displacement damage functions codified in National Standards are not currently available for other semiconductor materials.
1.2 Elements of this guide, with the deviations noted, may also be applicable to the exposure of semiconductors comprised of other materials except that validated 1-MeV displacement damage functions codified in National standards are not currently available.
1.3 Only the conditions of exposure are addressed in this guide. The effects of radiation on the test sample should be determined using appropriate electrical test methods.
1.4 This guide addresses those issues and concerns pertaining to irradiations with neutrons.
1.5 System and subsystem exposures and test methods are not included in this guide.
1.6 The range of interest for neutron fluence in displacement damage semiconductor testing range from approximately 109 to 1016 1-MeV n/cm2.
1.7 This guide does not address neutron-induced single or multiple neutron event effects or transient annealing.
1.8 This guide provides an alternative to Test Method 1017, Neutron Displacement Testing, a component of MIL-STD-883 and MIL-STD-750.
1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
|2. Referenced Documents|
Wollen Sie sich sicher sein, dass Sie nur die gültigen technischen Normen verwenden?
Wir bieten Ihnen eine Lösung, die Ihnen eine Monatsübersicht über die Aktualität der von Ihnen angewandten Normen sicher stellt.
Brauchen Sie mehr Informationen? Sehen Sie sich diese Seite an.
Letzte Aktualisierung: 2018-11-20 (Zahl der Positionen: 2 194 828)
© Copyright 2018 NORMSERVIS s.r.o.