Cookies
Wir benötigen Ihre Einwilligung zur Verwendung der einzelnen Daten, damit Sie unter anderem Informationen zu Ihren Interessen einsehen können. Klicken Sie auf "OK", um Ihre Zustimmung zu erteilen.
ASTM F1667-15
Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
Automatische name übersetzung:
Standard-Spezifikation für Driven Fasteners : Nägel , Spikes und Staples
NORM herausgegeben am 1.9.2015
Informationen über die Norm:
Bezeichnung normen: ASTM F1667-15
Anmerkung: UNGÜLTIG
Ausgabedatum normen: 1.9.2015
SKU: NS-618478
Zahl der Seiten: 47
Gewicht ca.: 141 g (0.31 Pfund)
Land: Amerikanische technische Norm
Kategorie: Technische Normen ASTM
Kategorie - ähnliche Normen:
Die Annotation des Normtextes ASTM F1667-15 :
Keywords:
diameter, driven fasteners, head, length, nails, point, spikes, staples,, ICS Number Code 21.060.01 (Fasteners in general)
Ergänzende Informationen
| 1. Scope | ||
|
1.1 This specification covers nails, spikes, staples, and other driven fasteners, as listed in Table 1. Note 1: Fastener ductility information is presented in
Table 2 and dimensional
information in Tables 3–65.
† Editorially corrected in March
2012.
L
|
= |
length, in., |
|
H |
= |
head diameter, in., |
|
TL |
= |
length of threaded shank, in., |
|
max |
= |
maximum acceptable value (not subject to tolerances), |
|
min |
= |
minimum acceptable value (not subject to tolerances), |
|
D |
= |
shank diameter, in., |
|
T1 |
= |
crest diameter, in., and |
|
P |
= |
pitch, or spacing of threads, in. |
L
=
length, in.,
H
=
head diameter, in.,
TL
=
length of threaded shank, in.,
max
=
maximum acceptable value (not subject to tolerances),
min
=
minimum acceptable value (not subject to tolerances),
D
=
shank diameter, in.,
T1
=
crest diameter, in., and
P
=
pitch, or spacing of threads, in.
Dimensions and Tolerances for Gages of Flat Top Crown Staples
10 Gage
12 Gage
14 Gage
15 Gage
16 Gage
18 Gage
T
W
T
W
T
W
T
W
T
W
T
W
Nominal
.1250
.1400
.0935
.1120
.0735
.0855
.0673
.073
.0563
.064
.038
.050
Maximum
.1290
.1440
.0975
.1160
.0775
.0895
.0731
.076
.0626
.068
.0415
.0532
Minimum
.1210
.1360
.0895
.1080
.0695
.0815
.0615
.070
.0500
.060
.0345
.0468
Tolerance
±
.0040
.0040
.0040
.0040
.0040
.0040
.0058
.003
.0063
.004
.0035
.0032
1.2 Fasteners described in this
specification are driven by hand tool, power tool, or mechanical
device in single or multiple strikes and are positioned by hand,
tool, or machine.
1.3 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.
1.4 Fasteners in this specification are sold in bulk (loose) form and are collated for loading into the magazine of an application tool. Other than as covered in Section 9, Workmanship, cohering materials (including, but not limited to, plastic, adhesive bond, paper tape, plastic strip, plastic carrier, wire, etc.) and relative orientation of collated fasteners are not within the scope of this standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
|
Standard Test Methods for Nails |
|
|
Standard Test Method for Determining Bending Yield Moment of Nails |
|
|
Standard Terminology of Collated and Cohered Fasteners and Their Application Tools |
|
|
Standard Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware |
|
|
Standard Specification for General Requirements for Wire Rods and Coarse Round Wire, Carbon Steel [Metric] (Withdrawn 2011) |
|
|
Standard Specification for Zinc-Coated (Galvanized) Carbon Steel Wire |
|
|
Standard Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel |
|
|
Standard Terminology of Nails for Use with Wood and Wood-Base Materials |
Empfehlungen:
Aktualisierung der technischen Normen
Wollen Sie sich sicher sein, dass Sie nur die gültigen technischen Normen verwenden?
Wir bieten Ihnen eine Lösung, die Ihnen eine Monatsübersicht über die Aktualität der von Ihnen angewandten Normen sicher stellt.
Brauchen Sie mehr Informationen? Sehen Sie sich diese Seite an.
