Wir benötigen Ihre Einwilligung zur Verwendung der einzelnen Daten, damit Sie unter anderem Informationen zu Ihren Interessen einsehen können. Klicken Sie auf "OK", um Ihre Zustimmung zu erteilen.
Standard Specification for Chromium Free Zinc-Flake Composite, with or without Integral Lubricant, Corrosion Protective Coatings for Fasteners
Name übersetzen
NORM herausgegeben am 1.12.2019
Bezeichnung normen: ASTM F3019/F3019M-19
Ausgabedatum normen: 1.12.2019
SKU: NS-983454
Zahl der Seiten: 4
Gewicht ca.: 12 g (0.03 Pfund)
Land: Amerikanische technische Norm
Kategorie: Technische Normen ASTM
This specification establishes the basic requirements for non-electrolytically applied zinc-flake composite corrosion protective coating systems for fasteners. The requirements apply to appearance, adhesion, corrosion resistance, blisters, thread fit, hydrogen embrittlement, and total coefficient of friction. The coating systems covered by this specification do not contain hexavalent chromium, lead, cadmium, or mercury. This specification is intended for corrosion protection of inch and metric series threaded fasteners as well as for non-threaded fasteners such as washers and pins. This specification also covers test methods, application, inspection, and certification.
Keywords:
basecoat, coating, corrosion, dip-drain, dip-spin, embrittlement, fasteners, flake, friction, inorganic, non-electrolytically, organic, protection, resistance, rust, spray, topcoat, zinc,, ICS Number Code 87.040 (Paints and varnishes)
1. Scope | ||||||||||||||||||||||||||||||
1.1 This specification covers the basic requirements for non-electrolytically applied zinc-flake composite corrosion protective coating systems for fasteners (See Note 1). Note 1: The coating systems do not contain hexavalent
chromium, lead, cadmium, or mercury.
1.2 This specification is intended for corrosion protection of inch and metric series threaded fasteners with minimum nominal diameters of 0.250 in. for inch series and [6.00 mm] for metric as well as for non-threaded fasteners such as washers and pins. 1.3 This coating system may be specified to consist of a zinc-flake basecoat, or a zinc-flake basecoat and topcoat (See Note 2). Note 2: For threaded fasteners, the coating system will
typically consist of a zinc-flake basecoat and topcoat.
1.3.1 The basecoat is a zinc-rich material containing aluminum flakes dispersed in a compatible liquid medium. The zinc-flake basecoat may be specified to contain integral lubricant. 1.3.2 Topcoats may be organic or inorganic in composition depending upon the specified requirements. 1.3.2.1 Organic topcoats consist of polymer resins, aluminum, dispersed pigments, and are colored in their applied state. 1.3.2.2 Inorganic topcoats consist of water-dispersed silicate compounds and are transparent in their applied state. 1.3.2.3 Topcoats contain integral lubricants and are applied in conjunction with zinc-flake basecoats to form a coating system with enhanced performance attributes such as increased corrosion resistance, total coefficient of friction properties, chemical resistance, and color. 1.4 These zinc-flake basecoats and topcoats are applied by conventional dip-spin, dip-drain, or spray methods to fasteners which can be handled through a cleaning, coating, and curing operation. The maximum curing temperature is 482 °F [250 °C]. 1.5 The friction properties of the coating system may be determined by a standard test to verify process control or by a part specific test which requires the purchaser to establish and communicate technical criteria. 1.6 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||||||||||||||||
2. Referenced Documents | ||||||||||||||||||||||||||||||
|
Bereitstellung von aktuellen Informationen über legislative Vorschriften in der Sammlung der Gesetze bis zum Jahr 1945.
Aktualisierung 2x pro Monat!
Brauchen Sie mehr Informationen? Sehen Sie sich diese Seite an.
Letzte Aktualisierung: 2024-05-16 (Zahl der Positionen: 2 902 054)
© Copyright 2024 NORMSERVIS s.r.o.