Vorsicht!

In Ihrem Browser ist die Javascript-Aktivierung nicht erlaubt. Einige Funktionen mögen nicht richtig funktionieren. Für vollständige Funktionalität des Internet-Geschäfts empfehlen wir Javascript zu aktivieren. Siehe hier Instruktion, wie man im Ihren Web-Browser JavaScript aktiviert.

Angezeigte Währung: €

Preisanzeige: ohne MWS

Ergänzende Informationen

ASTM F2763-11

Standard Specification for 30 to 60 in. [750 to 1500 mm] Triple Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications

Automatische name übersetzung:

Standard-Spezifikation für 30 bis 60 in. [750-1500 mm] Triple-Profil-Wand Polyethylen (PE) Rohre und Fittings für Kanalisation Anwendungen

NORM herausgegeben am 1.2.2011

Sprache
Realisierung	PDF - sofortiges Download - 69.80 € Gedruckt - 69.80 €
Zugänglichkeit	AUF LAGER
Preis	69.80 € ohne MWS
69.80 €

Informationen über die Norm:

Bezeichnung normen: ASTM F2763-11
Anmerkung: UNGÜLTIG
Ausgabedatum normen: 1.2.2011
SKU: NS-54493
Zahl der Seiten: 6
Gewicht ca.: 18 g (0.04 Pfund)
Land: Amerikanische technische Norm
Kategorie: Technische Normen ASTM

Drucken

Einem Bekannten abschicken

Anfrage

Kategorie - ähnliche Normen:

Drainage systems

Die Annotation des Normtextes ASTM F2763-11 :

Keywords:
fittings, interior liner, PE, pipe, polyethylene, profile wall, sanitary sewer, ICS Number Code 91.140.80 (Drainage systems)

Ergänzende Informationen

1. Scope

1.1 This specification covers requirements and test methods for triple profile wall polyethylene pipe and fittings. The nominal inside diameters covered are 30 to 60 in. [750 to 1500 mm].

1.2 The requirements of this specification are intended to provide pipe and fittings suitable for underground use for non-pressure sanitary sewer systems. Pipe and fittings produced in accordance with this specification shall be installed in compliance with Practice D2321.

1.3 This specification covers pipe and fittings with an essentially smooth interior and exterior wall using an annular corrugated profile middle wall (Fig. 1).

1.4 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.5 The following precautionary caveat pertains only to the test method portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents

LRFD, Section 12	AASHTO LRFD Bridge Design Specifications Section 12 Buried Structures and Tunnel Liners
Fed. Std. No. 123	Marking for Shipment (Civil Agencies)
MIL-STD-129
NCHRP Report 631	Updated Test and Design Methods for Thermoplastic Drainage Pipe
D2444-21	Standard Practice for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight)
D3212-21	Standard Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals
D3350-21	Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
D4218-20	Standard Test Method for Determination of Carbon Black Content in Polyethylene Compounds by the Muffle-Furnace Technique
F412-23	Standard Terminology Relating to Plastic Piping Systems
F477-14(2021)	Standard Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe
D1600-18	Standard Terminology for Abbreviated Terms Relating to Plastics (Withdrawn 2024)
F2136-18(2024)	Standard Test Method for Notched, Constant Ligament-Stress (NCLS) Test to Determine Slow-Crack-Growth Resistance of HDPE Resins or HDPE Corrugated Pipe
D578/D578M-23	Standard Specification for Glass Fiber Strands
A666-23	Standard Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar
D618-21	Standard Practice for Conditioning Plastics for Testing
D2122-22	Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D2321-20	Standard Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications
D2412-21	Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading

ASTM F2763-11

Automatische name übersetzung:

Informationen über die Norm:

Kategorie - ähnliche Normen:

Die Annotation des Normtextes ASTM F2763-11 :

Ergänzende Informationen

Ähnliche Normen: